Exhaust page help!!!.

Topic: Exhaust page help!!!. (Read 1179 times) previous topic - next topic

Exhaust page help!!!.

December 26, 2006, 06:09:11 PM

Hello,

I found a scanned dual exhaust af o 87-88 TC 2.3 dual exhaust from a Ford book, But I need the 83-85 duals Mustang 302 Ford book page, this will be very very appreciated...

I need this only to compare the tail pipes, cauz the guy supposed sold to Me his duals from his Coug, changed his mind, and I want to see to purchase the right tail pipe (right side) for My 85 Bird...

The TC tailpipes is no longer available anywhere in My area, so I'll purchase a stang tailpipe and I'll length it, thats it!...

Thank You...

Exhaust page help!!!.

Reply #1 – December 26, 2006, 08:27:30 PM

just order the tail pipes from an '87-'93 5.0L Mustang LX. They will fit, you just need to add exhaust tips to them to make them reach the back of the car.

Exhaust page help!!!.

Reply #2 – December 26, 2006, 09:04:45 PM

Hello,

Okay thank You very much, I guessed the mustang tail fit on a Bird, but I believed was around the same year of Bitd I have...

Okay, I'll order one tomorrow...

Thank You again...

Quote from: 1WLD BRD;120156

just order the tail pipes from an '87-'93 5.0L Mustang LX. They will fit, you just need to add exhaust tips to them to make them reach the back of the car.

Exhaust page help!!!.

Reply #3 – December 28, 2006, 12:05:33 AM

THe only problem you might have is the brake hose on the rear. Just check it to make it will not get burn on the right tail pipe.

Exhaust page help!!!.

Reply #4 – December 28, 2006, 09:33:13 PM

Hi,

I justb come from the Canadian Tire, and he have only a 1986 stang 5.0 right tail pipe in stock for $46.00 CDN bucks, I purchased and I'll return if is not fit, but when arrived at home I putted a used tc left pipe and the stang pipe just purchased, and it seem good, heres a pics of that...

5.0 Fastcat, I'll jackstand My bird tomorrow or saturday, and i'll check all of these jacked and unjacked...

Send Me Your impressions...

Exhaust page help!!!.

Reply #5 – December 29, 2006, 01:52:53 AM

those are the same tailpipes I ran on my '85 Cougar, cheap, but it gets the job done. I just cut off the hanger welded towards the ler, and used those universal hangers at CTC.

Now just get the drivers side, and you are all set. Then weld some nice chrome tips on it.

Exhaust page help!!!.

Reply #6 – December 29, 2006, 02:59:53 AM

Hello ! 1WLD BIRD.

Yes, I'll cut the hanger plate on the stang pipe, cauz the Bird is hang by the ler, I have an hanger I pulled off on another bird/cougar at the syard last year, I'll install on the right side of My car, and this hanh the ler on the car...

For the hanging rod at the end of the stang pipe, I'll take the one is on the old pipe in the pic, but before all of this, I'll lenght the stang pipe (the new pipe on the floor on the pics), I'll weld with a mig, that's all...

For the rear out of the car, I'll probably put a little chrome "Y" pipes, or a rectangular end chrome tube, I'll choose this at the end of all...

First, I'll cut My front "Y" pipe, and run straight from the down pipes to the lers...

My left pipe is the same diameter of the stang pipe I have, and it's virtually new, I installed the complete new single exhaust last winter and have around 3-4000 miles...

I'll keep My stock ler for the left side, and purchase another one for the right side, I guess the output sound will not bad for a V6...

I don't need a very louder sound, just a twin exhaust, I make My own twin exhaust on all of My past car, and I'll love that!...

I'll post the pics of finished works when I'll done and an stereo audio file of that IF I like the sound...

Happy holydays,