Power windows Reply #15 – October 03, 2010, 05:11:21 PM Oh, duh, yeah I did that as well. Maybe I need to start tracing the wiring back from the motor connections to see if there is a break/cut ? Quote Selected
Power windows Reply #16 – October 03, 2010, 05:17:32 PM While you have the black wires grounded check the other wires on the switch to see if they are getting power while you move the switch up and down that will verify if the switch is good Do that for both switches before you start to go else where Quote Selected
Power windows Reply #17 – October 03, 2010, 05:20:04 PM Going to check that right now (there are 2 black wires on each switch, should I ground both at the same time?) QuoteDo that for both switches before you start to go else where I'm pretty confident the pass. side switch is good, I can hear the motor wanting to turn, it's prob. got bad brushes. Quote Selected
Power windows Reply #18 – October 03, 2010, 05:27:18 PM Quote from: 20thanniver-ls;337786Going to check that right now (there are 2 black wires on each switch, should I ground both at the same time?) I'm pretty confident the pass. side switch is good, I can hear the motor wanting to turn, it's prob. got bad brushes.Yes ground them both, the switch should send power where it needs to go ...and I DO have switches that I can hook you up with if yours is in fact bad :D And You are probably on track with the passenger side . Quote Selected
Power windows Reply #19 – October 03, 2010, 05:28:03 PM here's a silly question.. are you pressing the switch while checking the other wires for voltage? Quote Selected
Power windows Reply #20 – October 03, 2010, 05:29:49 PM Quote from: turbo_88_XR7;337789here's a silly question.. are you pressing the switch while checking the other wires for voltage?Oh god ,I hope so Quote Selected
Power windows Reply #21 – October 03, 2010, 05:31:50 PM that's why i asked LOL have to do the same when checking power at the motor Quote Selected
Power windows Reply #22 – October 03, 2010, 05:37:54 PM Yea, I had my son pressing the switch LOLAlright, I grounded both wires on the drivers window switch, put a meter to all but the black wires, and the only one that had any voltage was the red/light blue that had voltage before. Did the same with the passenger side (excpept without the grounding) and the other 3 wires (other than the red/lb one was yellow, and one was solid red, I beleive) all had voltage while pressing the switch. I think I'm good on the pass. side, other than needing a new motor. I'm beginning to think that power is getting to the driver's side switch, and stopping there. Quote Selected
Power windows Reply #23 – October 03, 2010, 05:40:13 PM Quote from: 20thanniver-ls;337794Yea, I had my son pressing the switch LOLAlright, I grounded both wires on the drivers window switch, put a meter to all but the black wires, and the only one that had any voltage was the red/light blue that had voltage before. Did the same with the passenger side (excpept without the grounding) and the other 3 wires (other than the red/lb one was yellow, and one was solid red, I beleive) all had voltage while pressing the switch. I think I'm good on the pass. side, other than needing a new motor. I'm beginning to think that power is getting to the driver's side switch, and stopping there.Sounds like you have a bad switch on the drivers side and motor issues on the passenger side, I would like you to try one more thing please Swap the switches and see what you have on the drivers side . I'll wait right here again Quote Selected
Power windows Reply #24 – October 03, 2010, 05:41:36 PM I will do it. May take me a minute so hold on... Quote Selected
Power windows Reply #25 – October 03, 2010, 05:44:58 PM Wouldn't I have to swap wires from one to another since they are both connected to the same harness? Quote Selected
Power windows Reply #26 – October 03, 2010, 05:49:10 PM no the switch just pops out hang on ill snap a pic of one Quote Selected
Power windows Reply #27 – October 03, 2010, 05:51:25 PM the switch panel in your trunk may have been a replacement for the 1 currently in the car Quote Selected
Power windows Reply #28 – October 03, 2010, 06:00:40 PM Oh, Ok I see, give me a few minutes, I'll let you know Quote Selected
Power windows Reply #29 – October 03, 2010, 06:17:52 PM Ok, swapped switches, on the drivers side, I had power to the red/lb wire(constant) and while switching I had power to the other two wires, And to the window motor connector, but still no motor movement, so I'm thinking I have 2 bad motors and one bad switch. Quote Selected