Skip to main content ↑ ↓
Topic: Stupid fuel rail question.... (Read 1675 times) previous topic - next topic

Stupid fuel rail question....

Reply #15 –
Every time my jet (I was the Crew Chief on 0037) left and was landing somehwere other than home (all the time),I had to go with it.Egypt,England,Guam,Phillipines,Iceland,Greenland,Australia,all over the U.S.,Hawaii,Iraq and related nearby areas,etc.I wish I got those frequent flier miles.My baby.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

Stupid fuel rail question....

Reply #16 –
The fuel lines in that link are made by professional products, which is a Chinese rip of manufacturer. That is why they are cheap.
Quote from: jcassity
I honestly dont think you could exceed the cost of a new car buy installing new *stock* parts everywhere in your coug our tbird. Its just plain impossible. You could revamp the entire drivetrain/engine/suspenstion and still come out ahead.
Hooligans! 
1988 Crown Vic wagon. 120K California car. Wifes grocery getter. (junked)
1987 Ford Thunderbird LX. 5.0. s.o., sn-95 t-5 and an f-150 clutch. Driven daily and going strong.
1986 cougar.
lilsammywasapunkrocker@yahoo.com
 

Stupid fuel rail question....

Reply #17 –
Dragging this up.  Just picked up a set of 94-95 specific rails.....CHEAP.
$20 from a local guy 5 minutes away.  It's amazing how much you notice about a part when it's removed from a vehicle. 

If you happen to come across a set of these for cheap, buy them.  VERY obvious advantages to the design just from looking at them.
-- 05 Mustang GT-Whipplecharged !!
--87 5.0 Trick Flow Heads & Intake - Custom Cam - Many other goodies...3100Lbs...Low12's!

Stupid fuel rail question....

Reply #18 –
Do they connect to the stock V8 fuel line?
88 Thunderbird LX: 306, Edelbrock Performer heads, Comp 266HR cam, Edelbrock Performer RPM intake, bunch of other stuff.

Stupid fuel rail question....

Reply #19 –
Yes.  The fittings are the same sizes, the angles are slightly different so you CAN use the stock lines, but you'll have to play with them a bit.  The return line will be at a strange angle going in.

A buddy has a junked 95.......Had no rails though.......I'm gonna take the lines from it as it will make for a cleaner look.

FYI -- the regulator is different as well.
-- 05 Mustang GT-Whipplecharged !!
--87 5.0 Trick Flow Heads & Intake - Custom Cam - Many other goodies...3100Lbs...Low12's!

Stupid fuel rail question....

Reply #20 –
So it's not a direct swap. Not like I need bigger fuel rails at my power level though.;)
88 Thunderbird LX: 306, Edelbrock Performer heads, Comp 266HR cam, Edelbrock Performer RPM intake, bunch of other stuff.

Stupid fuel rail question....

Reply #21 –
No, but its close I can get the Kirban adjustable 94-95 regulator cheap enough.

Great article here that mentions perhaps using a pipe bender on the Fox steel lines to bend them to conform nicely to the 94-95 rails......
http://www.wazees.com/media/3488/sn95fuel-rail.pdf

My next option was the Professional Products 86-93 fuel rail kit.  With the regulator that has to be used with those rails price is about $200..... I can do this for under $100.....

My intake spacer makes it so that I don't even have to pull the upper to accomplish any of this.
-- 05 Mustang GT-Whipplecharged !!
--87 5.0 Trick Flow Heads & Intake - Custom Cam - Many other goodies...3100Lbs...Low12's!