Skip to main content
Topic: WANTED: Hoods, Trannies...entire car? :P (Read 708 times) previous topic - next topic

WANTED: Hoods, Trannies...entire car? :P

I'd like to get my filthy mitts on a TC hood but they are a tough find out here in the desert.

Also looking for a C4 OR AOD transmission that has either been recently rebuilt (for all of you shop employees) or one that hasn't been run into the dirt.  My original intent was to pick up a TCI C4, but time constraints have made that rather unfeasible.

A set of headers would be great too.  I've seen a few listed, but most have been sold.

I'll pay ship.

WANTED: Hoods, Trannies...entire car? :P

Reply #1
I have a tranny but I assume iowa is a little far for you to ship from.

WANTED: Hoods, Trannies...entire car? :P

Reply #2
Quote from: 86XR7project;270887
I have a tranny but I assume iowa is a little far for you to ship from.


ya, me 2, and i dont think it 'd be cheap......
[/IMG]
Just enjoyin the ride!!!!

WANTED: Hoods, Trannies...entire car? :P

Reply #3
TBH idk what freight would be like.  relatively new field for me.

WANTED: Hoods, Trannies...entire car? :P

Reply #4
i have a complete 88 TC hood...$100 plus shipping.

WANTED: Hoods, Trannies...entire car? :P

Reply #5
I'm not to sure how you would find out.

WANTED: Hoods, Trannies...entire car? :P

Reply #6
If you can settle for a C5 I have a rebuilt one that you can buy for $400 if you remove.  I'd help.  5,000 miles since the rebuild.  It's not a Loooong drive from where you are.  If you are near Pheonix probably about 10 hours or so.
Armed Forces Car Club
Eastern Sierra Chapter, California
WEB:  armedforcescarclub.com

WANTED: Hoods, Trannies...entire car? :P

Reply #7
I was just looking with UPS and it would be around $150 to ship plus what I'd want. Don't know if that would be in your ballpark.

WANTED: Hoods, Trannies...entire car? :P

Reply #8
frieghtquote.com
cost $72 to ship a TC rear end from eastern Pa, to western NY
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook

 

WANTED: Hoods, Trannies...entire car? :P

Reply #9
I still have this one. I could pallet it.
http://www.foxtbirdcougarforums.com/showthread.php?t=19763
Old Grey Cat to this.88 Cat, 5.0 HO, CW mounts, mass air, CI custom cam, afr165's, Tmoss worked cobra intake, BBK shorty's,off road h pipe, magnaflow ex. T-5,spec stage 2 clutch, 8.8 373 TC trac loc, che ajustables with bullits on the rear. 11" brakes up front. +

WANTED: Hoods, Trannies...entire car? :P

Reply #10
We've got about a dozen 87/88 TC hoods for $50 each. None of them are perfect though, they all have some dings in them. I know people who go back and forth between AZ and MN, but it's usually in the spring and fall. Anyway, just tossing it out. Good luck.
1987 Turbo Coupe - Son's car
1987 Super Coupe - Son's project car
1934 Ford - My project car