Skip to main content ↑ ↓
Topic: How much you think it'd cost to fix this?!? (Read 3870 times) previous topic - next topic

How much you think it'd cost to fix this?!?

Reply #15 –
There's nothing really structural behind the damage area other then the lower vertical brace inside the trunk well.
the entire panel itself is the structural part of the car, tying the roof to the frame so to speak (making it a short story)

Is that the only pic you got  from him?

I would check the cross-brace behind the back seat and the trunk wells real good. if you really wanted to measure to check the frame, I have the specs on the frame rails and measuring points. but you would need to jack it up to get under it to measure

also check the outer inside wheel well for damage. if it's damaged, another panel won't line up without repairing it

also look down the other side of the car with a light, but not in bright outdoor light. it will be easier to see ripples or waves that might have occurred from the accident. Dusk would be the best time to check for dents and ripples. But I don't think there is any frame damage by looking at that pic. but you never know until you see the entire car up close

this is whats behind the quarter panel
there's a little support in the front. but its in the inside of the car


here's the brace inside the trunk well
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

How much you think it'd cost to fix this?!?

Reply #16 –
I think shop rate is $75 hr.
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

How much you think it'd cost to fix this?!?

Reply #17 –
good tips, thanks!  This is really tough.  Could be a great car but I'm getting $3000+ quotes!  I could take the to San diego city college auto body or learn myself somehow.  I guess either way it will atleast be WAY better and ok to drive to shows and meets...  Then i can have it redone all-out later on.  I'd really like to learn this stuff just don't know if I could do it where I am...  Guess maybe the auto shop on the local marine base where my buddy works...?
1988 Thunderbird Turbo Coupe
'89 5.0 w/ ported intakes, Mallory Adjustable FPR, BBK shorties and H with 2.5" Flows, 130 amp 3G, 89 Mustang comp/wiring, Aluminum radiator w/ elec fan, T5 trans, King Cobra clutch, 3.55 gears, 13" Cobra brakes (front), Wilwood prop valve, Mustang A-arms, Front Coil-overs, MM CC plates, Silver 17x9 R's, 03 Cobra IRS, Aluminum DS, 2002 Mustang dash/console etc..., custom leather seats

How much you think it'd cost to fix this?!?

Reply #18 –
I would get it, pound it out as much as you can, and just drive it for now
u can get at the panel if u remove the back seat and sail panels, and u can pound the back part from inside the trunk.
i cant see spending 3k on a car your gonna pay much less then half of that on the car. 3k on one area is insane.
RIP 1988 and 1990 Lincoln Mark VII LSC
I welcomed the dark side and currently am driving a 2000 Dodge Durango SLT plus, with a 5.9, Code named project "Night Runner"
Shes black on black, fully loaded, with headers, 180 tstat, e fan, straight exhaust into a cherry bomb vortex ler, full tune up, ported intake and T/B, MSD coil, and round aircleaner.
Mods to come: Fully rebuilt and heavily modded 46RE, and a richmond rachet locker.
my $300 beater ;)
R.I.P Kayleigh Raposa 12/18/90 - 2/24/07

How much you think it'd cost to fix this?!?

Reply #19 –
yeah, but when you figure it'd cost that much to fix the current car anyway, I'd rather start with one that is dry and nice on the bottom.  I'll look into the school auto body shop too...
1988 Thunderbird Turbo Coupe
'89 5.0 w/ ported intakes, Mallory Adjustable FPR, BBK shorties and H with 2.5" Flows, 130 amp 3G, 89 Mustang comp/wiring, Aluminum radiator w/ elec fan, T5 trans, King Cobra clutch, 3.55 gears, 13" Cobra brakes (front), Wilwood prop valve, Mustang A-arms, Front Coil-overs, MM CC plates, Silver 17x9 R's, 03 Cobra IRS, Aluminum DS, 2002 Mustang dash/console etc..., custom leather seats

How much you think it'd cost to fix this?!?

Reply #20 –
well for now it shouldnt be bad to just do that.
Its all how much work you wanna do!
Trust me I know the feeling, I would love to get another and replace my car, its so rotted, and filled with fiberglass patches!
RIP 1988 and 1990 Lincoln Mark VII LSC
I welcomed the dark side and currently am driving a 2000 Dodge Durango SLT plus, with a 5.9, Code named project "Night Runner"
Shes black on black, fully loaded, with headers, 180 tstat, e fan, straight exhaust into a cherry bomb vortex ler, full tune up, ported intake and T/B, MSD coil, and round aircleaner.
Mods to come: Fully rebuilt and heavily modded 46RE, and a richmond rachet locker.
my $300 beater ;)
R.I.P Kayleigh Raposa 12/18/90 - 2/24/07

How much you think it'd cost to fix this?!?

Reply #21 –
I could never get a replacement for mine.
Although I wouldn't mind finding it a friend. :D
Yes, I already have my next project planned
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

How much you think it'd cost to fix this?!?

Reply #22 –
Lol!!  Nice.  It's hard for me too...  First car I bought. :(

Does anyone know a good source of tutorials on a job like this?
1988 Thunderbird Turbo Coupe
'89 5.0 w/ ported intakes, Mallory Adjustable FPR, BBK shorties and H with 2.5" Flows, 130 amp 3G, 89 Mustang comp/wiring, Aluminum radiator w/ elec fan, T5 trans, King Cobra clutch, 3.55 gears, 13" Cobra brakes (front), Wilwood prop valve, Mustang A-arms, Front Coil-overs, MM CC plates, Silver 17x9 R's, 03 Cobra IRS, Aluminum DS, 2002 Mustang dash/console etc..., custom leather seats

How much you think it'd cost to fix this?!?

Reply #23 –
Mabe,
what's it worth to you?
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

How much you think it'd cost to fix this?!?

Reply #24 –
That brace behind the drs 1/4 panel is just for the spare tire to mount to from the way it looks.
The pass side has no bracing like that at all,so why would it be structural on one side and not the other????
Also there would be no reason to install a structural brace in an are such as behind the rear tire,no stress is projected there that needs bracing.
If you don't need your spare just cut it out.

How much you think it'd cost to fix this?!?

Reply #25 –
That explains why there nothing in the pass. side. I always had a full size spare
I didn't even think of that. I knew it wasn't attached to the panel for support.
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

How much you think it'd cost to fix this?!?

Reply #26 –
how much is what worth to me??  The car or the tutorials??
1988 Thunderbird Turbo Coupe
'89 5.0 w/ ported intakes, Mallory Adjustable FPR, BBK shorties and H with 2.5" Flows, 130 amp 3G, 89 Mustang comp/wiring, Aluminum radiator w/ elec fan, T5 trans, King Cobra clutch, 3.55 gears, 13" Cobra brakes (front), Wilwood prop valve, Mustang A-arms, Front Coil-overs, MM CC plates, Silver 17x9 R's, 03 Cobra IRS, Aluminum DS, 2002 Mustang dash/console etc..., custom leather seats

How much you think it'd cost to fix this?!?

Reply #27 –
LOL-
Check out the main home page of the link I sent you
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

How much you think it'd cost to fix this?!?

Reply #28 –
oops, oh yeah, I should have known that one!!
1988 Thunderbird Turbo Coupe
'89 5.0 w/ ported intakes, Mallory Adjustable FPR, BBK shorties and H with 2.5" Flows, 130 amp 3G, 89 Mustang comp/wiring, Aluminum radiator w/ elec fan, T5 trans, King Cobra clutch, 3.55 gears, 13" Cobra brakes (front), Wilwood prop valve, Mustang A-arms, Front Coil-overs, MM CC plates, Silver 17x9 R's, 03 Cobra IRS, Aluminum DS, 2002 Mustang dash/console etc..., custom leather seats

How much you think it'd cost to fix this?!?

Reply #29 –
I had about the same damage(same side) to mine when the lady at the bank hit me about 1 1/2 years ago.
new rear quarter skin, tail light and whole car painted --$2600.00--
after pic.......

http://i216.photobucket.com/albums/cc154/flipnbird/DSCF0185-1.jpg
88 sport,TW heads, comp xe270hr, cobra u/Tmoss ported lower, 65 mm throttle body, under drives,smog delete,
1.7 roller rockers, cai, k&n, bbk adj regulator, 76mm Pro-m,all MSD ign. MSD dist,18° base timing, 3g alt.1 5/8 ceramic headers, 255lph walbro, 2.5" h-pipe, flowmasters, silverfox valvebody, 3.73 gear,
http://i216.photobucket.com/albums/cc154/flipnbird/DSCF0185.jpg ( RIP : ( )