Skip to main content ↑ ↓
Topic: Project Evolution *** Project Complete **** Wednesday July 9, 2014 (Read 1378876 times) previous topic - next topic

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2070 –
You should be able to use the drive shaft that was in the Cougar with the 5.0 AOD combo. I'm 99% certain that the 3.8 and 5.0 cars with AODs used the same length drive shaft.
88 Thunderbird LX: 306, Edelbrock Performer heads, Comp 266HR cam, Edelbrock Performer RPM intake, bunch of other stuff.

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2071 –
Quote from: thunderjet302;315950
You should be able to use the drive shaft that was in the Cougar with the 5.0 AOD combo. I'm 99% certain that the 3.8 and 5.0 cars with AODs used the same length drive shaft.


I never had that combo, so I'll try with the 3.8/ AOD combo. I'm pretty sure it won't be a problem.
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2072 –
i know there was a chart of the variouse drive shaft leingths years ago but im not sure where to find it now. It had a combo on 3.8-c6 then 3.8-AOD and 5.0-AOD.
2001 Buick Regal LS (DD):hick:

Got that fox rash again!

-Resident smartass! :ies:

- Don't listen to the naysayers. For every person who actually helps with your project there will be 10 who will discourage you all the while thinking that they are helping. 99% of all people have good intentions. That doesn't make them right.- XR7 Dave - SCCOA.Com

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2073 –
I'm pretty sure you can, because the trans mount still bolts to the same spot. The aod is no different externally!
Old Grey Cat to this.88 Cat, 5.0 HO, CW mounts, mass air, CI custom cam, afr165's, Tmoss worked cobra intake, BBK shorty's,off road h pipe, magnaflow ex. T-5,spec stage 2 clutch, 8.8 373 TC trac loc, che ajustables with bullits on the rear. 11" brakes up front. +

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2074 –
Quote from: Kitz Kat;315972
I'm pretty sure you can, because the trans mount still bolts to the same spot. The aod is no different externally!


X2.But,get a Crown Vic shaft and have it shortened before you need the driveshaft,Just start out with the aluminum one.They can be found wicked cheap at the yards,and well,you know the rest of the shortening story.;
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2075 –
you have to remember.... up here, good parts are expensive. not like where you live Vinnie
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2076 –
We're getting closer.








[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2077 –
I didn't know they cost a lot there.I actually thought they were cheaper. I did know they were rusty though.LOL.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2078 –
Wow... Wow..


WOW
[SIGPIC][/SIGPIC]
Operation: X Marks the Spot
5.0L SEFI, AOD, 8.8" 3.02 TracLok - All Stock

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2079 –
Quote from: vinnietbird;316017
I didn't know they cost a lot there.I actually thought they were cheaper. I did know they were rusty though.LOL.


Actually it's everything here is expensive from taxes, to gas, to food. Gotta go out west to the mts of New Mexico
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2080 –
And, I know the pics are a bit blurry. The flash was glaring of the car, and I had to shut the it off. Unfortunately, I didn't hold the camera steady long enough for the pics.
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2081 –
Out here,it's free to go into the yards,and when the guy says "$10.00",then it's $10.00....not "plus tax,etc.".Usually,I can fill a large duffel bag (I use it to tote parts at the yards) with a bunch of small parts and he'll ask for $20-25.00.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2082 –
The passenger door looks a little misaligned...or is the fender?
[SIGPIC][/SIGPIC]
5.0L Speed density
Explorer intake
'92 Mustang GT cam
GT-40 racing heads
Unequal length headers
Custom-made duals
19# injectors
65mm TB
AFPR
T/C header panel
11" brake upgrade
T/C rear sway bar
Electrical mods: too many to list :D
 

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2083 –
Quote from: Quietleaf;316048
The passenger door looks a little misaligned...or is the fender?

looks fine in the last pic. Unless I'm not seeing something.
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #2084 –
also, the doors are not closed. could be what your seeing. I spent 8 hrs aligning the entire front of the car one Saturday
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1