I'll retry here... February 21, 2007, 09:09:36 PM nobody was replyed on My question in another area, I'll guess here...When I have My front TC bumper for My 85 bird (If I receive before 2020), I want to see a pic of a bracket hold the fogs, I plan to make a oem style as possible, I guess it's not just a flat bar, this cause a vibrating on the fogs...Any pics or good explaination will be very appreciated...Have a nice Day,Dom... Quote Selected
I'll retry here... Reply #1 – February 21, 2007, 09:28:06 PM Yeesh, if I could find my camera anywhere I would snap a pic for you. I have an '85 Turbocoupe bumper and cover. As I recall it's just a piece of angle steel with a hole in it to bolt the fog light to. Quote Selected
I'll retry here... Reply #2 – February 21, 2007, 10:17:20 PM Its a piece of stamped 3/16" steel, I have a set somewhere with a bumper and lights.Scott Quote Selected
I'll retry here... Reply #3 – February 21, 2007, 10:18:57 PM I'll have to dig out my extras. It's not just a simple piece of angle iron.It is a BEEFY "C"-shaped piece of 3/16" steel. It takes alot to bend them. They are made as they are to protect the fog light from damage from below I imagine.Basically they bolt to the bumper at the top and there is a stud on the back of the light housing that then bolts to the back of the bracket. You'll need to modify your bumper as the TC ones had cutouts for the C-nuts. Quote Selected
I'll retry here... Reply #4 – February 21, 2007, 10:37:19 PM Quote from: Chuck W;130787I'll have to dig out my extras. It's not just a simple piece of angle iron.It is a BEEFY "C"-shaped piece of 3/16" steel. It takes alot to bend them. They are made as they are to protect the fog light from damage from below I imagine.Basically they bolt to the bumper at the top and there is a stud on the back of the light housing that then bolts to the back of the bracket. You'll need to modify your bumper as the TC ones had cutouts for the C-nuts.I beleived it was not just a flatbar, 3/16" thich on the road with around 5" long will vibrate a lot, I guess is a kind of angle torsionned to bolt on the bumper frame and behind the fog light 5/16 nut...If You found, please send Me a pic, otherwise I'll made a kind of "antivibrating" bracket...IF I receive My TC bumper purchased on ebay, paid the 02 Feb, and the seller say still not received?????, But I have some issue with the mail this time.Anyway, If I never receive the TC bumper and lost My $$$ I'll not make a crisis, but I'll cut My bumper cover and mold like the stock one, it's a pain and long, but I have the tools to work this neoprene/rubber...Thanks for Your help...Have a nice Day,Dom. Quote Selected
I'll retry here... Reply #5 – February 21, 2007, 10:43:03 PM Quote from: Ifixyawata;130775Yeesh, if I could find my camera anywhere I would snap a pic for you. I have an '85 Turbocoupe bumper and cover. As I recall it's just a piece of angle steel with a hole in it to bolt the fog light to.Don't go to dig in Your stuff for that, I asked ONLY to made the stock ones (cauz I have stock like new hella TC fogs), OR IF You found, I need only one bracket pic, I'll made the reverse if it's the case...The big issue is I'm not sure I receive the TC bumper I purchased at ebay, and I need the fogs for this summer, If I not receive the bumper cover I'll work a little lot to make a good job to have a nice and clean (oem like) TC bumper, and I'm pissed off working on My Bird (worked too long in the past in a bodywork)...Thank You very Much,Best regards, \\Dom. Quote Selected
I'll retry here... Reply #6 – February 21, 2007, 10:46:02 PM Quote from: tbirdscott;130786Its a piece of stamped 3/16" steel, I have a set somewhere with a bumper and lights.ScottHi!, same as IFIXYAWATTA, don't dig in Your stuff for nothing, if I don't found a pic I'll made My own brackets, and it will be skake proof, trust Me, I'll post the final result if I made My own brackets without the oem...Thanks a lot,Best regards,Dom. Quote Selected
Topic: I'll retry here... (Read 1128 times)
previous topic - next topic
