Skip to main content ↑ ↓
Topic: o2 sensor wiring (Read 1188 times) previous topic - next topic

o2 sensor wiring

Ok, so im getting ready to put in my o2 sensors, and i have to lengthen the wires, i have already cut them and my dumbass forgot to label the wires:hick:  theres 2 white and 1 black, of course i know the black connects to the black, but does it matter which white wire connects to its mate on the other end?
FOXLESS!!

1994 Lincoln Mark VIII

o2 sensor wiring

Reply #1 –
I did that a long time ago (I lengthened the harness on this car,and not the sensors),and what i did was,look at the relation of the wires in the sensor (placement of the three) to the wires on the plug (again,the placement of the wires),and was able to get the job done.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

o2 sensor wiring

Reply #2 –
That makes sense lol what would be the best type of heat wrap for the wires?
FOXLESS!!

1994 Lincoln Mark VIII

o2 sensor wiring

Reply #3 –
The two white wires are the heater, orientation makes no difference...

o2 sensor wiring

Reply #4 –
Quote from: TurboCoupe50;251995
The two white wires are the heater, orientation makes no difference...


I didn't know that.Cool.As far as wrapping them,I soldered mine,applied some heat shrink,and then some heat wrap sleeve (put the sleeve and heat shrink on BEFORE you do any wire connecting.LOL.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

o2 sensor wiring

Reply #5 –
Where did you get the heat sleeve from? I got the shrink tubing, and i went to Advance auto/Oreilly auto/ Auto zone and Lowe's and they all looked at me like i had three heads when i told them what i was doing and what i was looking for (i even called it a heat sleeve, they still had no clue...)
FOXLESS!!

1994 Lincoln Mark VIII

o2 sensor wiring

Reply #6 –
heat sleeve is a ceramic sleeve that most racer put on the spark plug wires from burning next to hot headers. they also wrap headers with it to keep the heat from the engine compartment. if you wrap your wiring it will keep the exhaust from burn your wiring.try summit racing .
remember it easier to fix them, than to find them after they been crushed.

V6 = juvenile delinquency!
 

o2 sensor wiring

Reply #7 –
I got mine some time ago at Autozone.My harness was wrapped with it from the factory.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..