Skip to main content ↑ ↓
Topic: Lets see your tailpipes (Read 6583 times) previous topic - next topic

Lets see your tailpipes

Reply #45 –
No pics today.The passenger side tip was too long and would hit the gas tank,so,new tips on the way,and updates as they happen.You heard it here first.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

Lets see your tailpipes

Reply #46 –
3" dynomax bullets (to mimick converters) 3" X pipe 3" 1 chamber flows
Flowmaster universal tailpipe kit,Stainless 3" tips

All done at home and it has a unique tone now

Opinions?

other then the car is nasty and needs waxed:D
[SIGPIC][/SIGPIC]
1974 maverick lsx powered turbo car SOLD
1973 maverick Tijuana Taxi Tribute
1957 chevy LSX Turbo project (race car)
Owner of Joe Dirt Fabrication

Lets see your tailpipes

Reply #47 –
 snow
[SIGPIC][/SIGPIC]
1974 maverick lsx powered turbo car SOLD
1973 maverick Tijuana Taxi Tribute
1957 chevy LSX Turbo project (race car)
Owner of Joe Dirt Fabrication

Lets see your tailpipes

Reply #48 –
Does the rear end ever hit the tailpipes?That setup intrigues me.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

Lets see your tailpipes

Reply #49 –
Quote from: vinnietbird;198176
Does the rear end ever hit the tailpipes?That setup intrigues me.



With it on the lift the rear does make light contact but nothing severe to cause damage.Absolutley no contact during driving.I was going to go over the axle but it is tight with 3" and i would have had to move my fuel lines and it still would had rubbed the control arms.
[SIGPIC][/SIGPIC]
1974 maverick lsx powered turbo car SOLD
1973 maverick Tijuana Taxi Tribute
1957 chevy LSX Turbo project (race car)
Owner of Joe Dirt Fabrication

Lets see your tailpipes

Reply #50 –
Sleeper: Is that with the SBC still installed? Looks nice!!

I want Stainless 3" Rolled Edge Tips and I want them to be vertical with the circular reverse lights on my car, the 83-84 tailights. Make it look that much more clean and nice. I'll have to go with a fuel cell though. I think the "pit" in the truck will make a nice place for a fuel cell.
"Real cars dont power the front wheels, they lift them"
[SIGPIC][/SIGPIC]
1984 Mercury Cougar GS 5.0:cougarsmily: BBK Equal Length Shorties, BBK O/R X-Pipe, Magnaflow Magnapacks, Mustang GT Stainless Tailpipes, 18" Magnaflow Rolled Edge Tips. Turbo Coupe Hood, Mach 1 Chin Spoiler. 17"x9" Cobra R's, Falken Ziex 255/50s, and 245/45s.
1984 Ford Thunderbird 3.8L "Drag Queen"
2009 Dodge Ram 1500 Lone Star Edition 5.7L Hemi 400hp, lex DOD14M Magnaflow retro-fit ler kit

Lets see your tailpipes

Reply #51 –
Quote from: cougrrr302;198190
Sleeper: Is that with the SBC still installed? Looks nice!!

I want Stainless 3" Rolled Edge Tips and I want them to be vertical with the circular reverse lights on my car, the 83-84 tailights. Make it look that much more clean and nice. I'll have to go with a fuel cell though. I think the "pit" in the truck will make a nice place for a fuel cell.




yep,and thanks the pics kinda make it look wierd
[SIGPIC][/SIGPIC]
1974 maverick lsx powered turbo car SOLD
1973 maverick Tijuana Taxi Tribute
1957 chevy LSX Turbo project (race car)
Owner of Joe Dirt Fabrication

Lets see your tailpipes

Reply #52 –
where did you get and how hard was it to install the aluminum gas lid?? I like it!!!!!!!!!!!!
88 sport,TW heads, comp xe270hr, cobra u/Tmoss ported lower, 65 mm throttle body, under drives,smog delete,
1.7 roller rockers, cai, k&n, bbk adj regulator, 76mm Pro-m,all MSD ign. MSD dist,18° base timing, 3g alt.1 5/8 ceramic headers, 255lph walbro, 2.5" h-pipe, flowmasters, silverfox valvebody, 3.73 gear,
http://i216.photobucket.com/albums/cc154/flipnbird/DSCF0185.jpg ( RIP : ( )

Lets see your tailpipes

Reply #53 –
Quote from: flipnbird;198193
where did you get and how hard was it to install the aluminum gas lid?? I like it!!!!!!!!!!!!



Its from walmart (lol) made for 97 and newer ford trucks it is as close to the right diameter as i could find there dirt cheap (11.99) and made of stainless
[SIGPIC][/SIGPIC]
1974 maverick lsx powered turbo car SOLD
1973 maverick Tijuana Taxi Tribute
1957 chevy LSX Turbo project (race car)
Owner of Joe Dirt Fabrication

Lets see your tailpipes

Reply #54 –
I have a 2004 Bullitt Mustang fuel door for my Bird.It was on the Blue T-Bird that's on the banner up top.It took a little ingenuity,but worth the time.I'll install it on the Sport after paint.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

Lets see your tailpipes

Reply #55 –
Here is an older pic.  I have since eliminated the gaudy clamps.
Blueprinted 306, Thumper ported Canfield 195's, TLSR Camshaft, custom motor mounts, Parker funnelweb, Pro Systems Carburetor, Tremec 3550 II, 4.30 gears, Moser Axles, Team Z custom suspension with upper relocation brackets and anti roll bar.  At the track I run M/T 26/10's on Weld Star rims.

My pipes

Reply #56 –
Here is an older pic of the Cougar at Tri State Raceway.  I have since eliminated the gaudy clamps.
Blueprinted 306, Thumper ported Canfield 195's, TLSR Camshaft, custom motor mounts, Parker funnelweb, Pro Systems Carburetor, Tremec 3550 II, 4.30 gears, Moser Axles, Team Z custom suspension with upper relocation brackets and anti roll bar.  At the track I run M/T 26/10's on Weld Star rims.

Lets see your tailpipes

Reply #57 –
Nice Cat.I also like the missing side trim.That's what I'm doing with my Sport.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

Lets see your tailpipes

Reply #58 –
sleeper, lets hear a sound clip of it....

Lets see your tailpipes

Reply #59 –
Um Side Pipes
[SIGPIC][/SIGPIC]