Random parts for sale out of my collection. I need to raise some funds and get rid of some stuff. Prices are all OBO, and do NOT include shipping. USED unless stated otherwise.
83-88 Thunderbird/Cougar:
CHE Black rear tubular control arms, upper and lower (barely used) - $150 SOLD
Tripminder w/plug (I was told it was TBird unit and a Crown Vic unit) - $35
Kaminari 83-86 Thunderbird 3-piece rear spoiler, in primer, complete, (this is the one with the long edges that match the bodyline) - $250
87-88 TC headlights, outer corners, and inner corners, clear with no clouding, low mileage examples - $250 set of 6
83-84 T-Bird driver's side taillight, lense only, with emblem - $25
83-84 T-Bird (TC) door panels, rear panels, etc, most all interior parts, in Desert Tan or Medium Gray, $5-$25 each
83-84 TC gauge pod - $25
87-88 TC gauge pod - $25 SOLD (1 Left)
87-88 T-Bird/Cougar "Star Wars" Gauges - $35
87-88 floor shifter, complete (5.0/AOD) - $75 SOLD
2.3T Engine:
Ford TTY/TTA Head Bolts, new in box (top opened) - $20 PENDING
87-88 IHI turbo, minimal shaft play, low mileage, complete with WGA and E6 with EGR tube (expensive shipping) - $250
87-88 Valve cover - $25
5.0 Engine:
ARP header studs and nuts, new in package (1 corner opened) - $35 SOLD
Universal:
B&M Roll Control (Line-Loc), new in the box - $50 SOLD
3" DynoMax Ultra-Flow Race bullet ler, new (P/N 24222) with a new 3" mandrel downturn - $50 PENDING
Tons and tons more, please ask.
I understand you might have some slightly used 2.3t head gaskets for sale?
Sorry, I had to :hick:
Hmm... a few things in that list look mighty compelling... I just might have to think about that shifter, assuming it's complete (cable, brackets, bezel, etc). Hmmm... do I wait for my 5-speed swap, or convert to floor shifter in the meantime?
you, Mike, for making me think about such things...
It's 100% absolutely complete. Hell, I'd throw in the tranny itself for some more $$$. It's even in Shadow Blue ;) Full center console and everything :D
And yes, I have 3 8993's, a 1035, and a VR for sale, slightly used :hick:
Obviously I'm raising fundage to fix Layla correctly (AND the Nissan truck).
pm'd
i'd be a liar if i said i wasn't interested in the line lock.
I bought an IHI for $35 bucks..
Good for you. Was it a 35K mile one complete with WGA, down elbow, inlet elbow, return line, and E6 with good EGR? I didn't think so.
re:
Mike: Are the CHE upper control arms the adjustable style? If so would you be willing to sell them seperate? Price with shipping to 02831? Pictures?
Thanks,
Rick
Some payments sent, marked as pending.
The CHE's are non-adjustable.
I'm actually kinda regretting buying my adjustable ones. The arse sits too high now, gotta get some shorter springs :hick:
...and by "too high" I mean "WAY TOO HIGH" - the 225/60R15 tires look like donut spares in the wheel wells now...
That's funny Carm! What, do embarrassed for pics? ;)
Updated
down pipe and ler if they dont sell let me know
You're like #27 in line. First guy sent a PayPal hold and then sent a m/o.
lol ok nvm then, figured that would be a nice gift for my dad
You want a pic? Here's a pic :hick: I'll either need to drop its butt or install something like 265/70R16 truck tires on the snowflakes to fill those gaping wheel wells...
holy hell!! thats all the way down? time for new springs/ or some drag slicks!
After seeing the pic.. is this what my CHE non adjustables will look like?
LOL! :hick: That's funny Carm! Time for some shorter Mustang springs ;)
That is all the frickin' way down. Stock '87 Turbo Coupe rear springs...
No. The adjustables add about an inch (or more, it seems to me) of height for the adjustment mechanism. The non-adjustables should have the car sitting at stock height.
what does a 83-84 TC gauge pod look like..... is there a pic around i can check out?... is that rpm, fuel and speedo? will it work with the aod speedo cable?
It has a tach and speedo and a boost gauge in it. I can snap a pic of the one I am selling.
The 83-84 TC cluster should look like a big speedo big tach, gas gauge in the middle. Then it has a green light for Boost and a red light for Overboost.
Yep, that's it exactly. Putting that cluster in a non-turbo car will result in the loss of a factory transmission gear indicator, though, since the fuel gauge is where the indicator is in non-turbo clusters.
no need, i have a floor shifter :)... could i swap it with my cougar digital dash.... i'm sure they'll be some wires to swap, but they'll fit and the speedo will work right?..... if so, i'll take that pic ;)
I know the one in my 84 T/c is a cable driven speedo. I think that the end that goes into the speedo are all the same. except the part that holds them onto the speedo.
My speedo cable is melted but still works. If my cluster comes out it's not going back in. I'll opt for the TC cluster when I replace it
*smacks forehead*
I totally spazzed on that... Stupid Auto... :p
If you take pics of the one your selling, Can you get one of the back for me please?
Want to make sure i put it all back together correctly. :hick:
Mike, do you have an 87-88 T-Bird driver's side quarter panel trim piece? I need a non-TC one with no cracks or chips. Mine has a hole in the front and it's been letting water in, which is one reason why I've got rust there.
I sure do! $25 plus shipping.
(http://i22.photobucket.com/albums/b325/Aesthetikz/cluster.jpg)
Like this, 'Cept i changed out the leds and rewired them, then covered the overboost and boost lettering.
Mike do u have a performance exhaust system? or if not a stock one for a 1986 Mercury Cougar LS 5.0L v8? Also Possiblely headers...??? Also do u have the fuel senser needed for the 87-88 T-Bird/Cougar "Star Wars" Gauges ?????? because if u have the stardard it works backwards and u need the other fuel senser to make it work correctly.
I have the fuel sender.
And I can get you performance exhaust new.
i need the rear drivers window how much?
TC or Sport :D
I have no chrome windows.
$15 plus shipping on a TC/Sport one.
How much for the fuel senser? and also What is a good exchaust to put on with long tube headers?
Mike, do you have another set of header studs?
Crusher,
$25 shipped for the sender. I like MagnaFlow and DynoMax products personally, and a full 2.5" mandrel-bent header-back with H-pipe is what you need ;)
FILA,
Nope, sure don't.
dare i ask how much a dash would cost shipped across the country?
While fixing mine today i snapped when all the fiberglass work i had just done got ruined:shoothead . Now it's a pile of shredded plastic and fiberglass..:macgun: .
Alright this Friday I will send u the $25.00 Dollars for the senser,
Is that Duel lers or single? with no converter or with converter ?
Crush. If you have a V8 or even a 6, it would be duals. Also depending on where your at, you may or may not need converters
By law I need Converters * BUT I DON'T WANT THEM * :-p I was surppose to get full length flow tech headers and custom H-pipe with dynomax super turbo lers and turn downs but that deal went down :S... SO I need a exchaust system and looking for something good for the street, not to race but I love to have the power :-p and I want long tube headers LOL :-p
Hum.... I *think* BBK has a H pipe for longtubes that has cats on it. From the H pipe back is up to you. Do you actually have to pass a smog test of just a visual inspection?
Nate,
DHL can truck it for about $125.
Crusher,
Duals.
how much for the exhaust system with lers and long tube headers?
Shoot me a PM.
PM Sent! :D